What is a 1/16" drill in decimal and mm?

0.0625 in, or 1.588 mm; nearest number / letter drill: #52 (0.0635 in, +0.0010 in); nearest metric drill: 1.6 mm (0.0630 in, +0.0005 in).

What RPM for a 1/16" drill in steel?

In low-carbon steel (1018) an HSS 1/16" drill (0.0625 in) runs about 5,500 RPM at 90 SFM; a carbide drill about 18,330 RPM at 300 SFM. RPM = 3.82 × SFM ÷ D.

What feed for a 1/16" drill?

About 0.0015 in/rev in mild steel, 0.0014 in/rev in aluminum and 0.0010 in/rev in 304 stainless. At 5,500 RPM that is 8.25 IPM in steel (IPM = RPM × IPR).

What RPM for a 1/16" drill in aluminum?

15,280 RPM with HSS (250 SFM) or up to 36,670 RPM with carbide (600 SFM), feeding about 0.0014 in/rev.

1/16" drill size

A 1/16" fractional drill is 0.0625 in (1.588 mm). It is the cut tap, 50% thread drill for 1-64.

Decimal inch: 0.0625
Millimeters: 1.588
Nearest 1/64: 1/16" (+0.0000)
Type: fractional drill

Nearest equivalents in other systems

Drills closest to 1/16"
System	Drill	Inch	mm	Difference
Number / letter	#52	0.0635	1.613	+0.0010 in
Metric	1.6 mm	0.0630	1.600	+0.0005 in

Speeds and feeds: in mild steel an HSS drill starts at about 5,500 RPM and 0.0015 in/rev (8.25 IPM); in 6061 aluminum about 15,280 RPM.

1/16" drill speeds and feeds by material

Jobber-length twist drill, D = 0.0625 in. RPM = 3.82 × SFM ÷ D, rounded to 10. Feed per rev scales with diameter and material; IPM = RPM × IPR.

1/16" drilling speeds
Material	HSS SFM	HSS RPM	Carbide SFM	Carbide RPM	Feed (in/rev)	HSS IPM	Carbide IPM
Aluminum (6061)	250	15,280	600	36,670	0.0014	21.4	51.3
Brass / free-machining	150	9,170	400	24,450	0.0012	11.0	29.3
Low-carbon steel (1018)	90	5,500	300	18,330	0.0015	8.25	27.5
Alloy steel (4140, annealed)	70	4,280	250	15,280	0.0015	6.42	22.9
Stainless 304	40	2,440	150	9,170	0.0010	2.44	9.17
Gray cast iron	80	4,890	250	15,280	0.0009	4.40	13.8
Titanium 6Al-4V	25	1,530	100	6,110	0.0008	1.22	4.89
Plastics (acetal)	300	18,330	500	30,560	0.0025	45.8	76.4

Small drills: the computed RPM is above most spindles. Run at your spindle's maximum and keep the feed per rev; feed drops in proportion.

Metric: Vc (m/min) = SFM × 0.3048; feed (mm/rev) = in/rev × 25.4. In steel, 5,500 RPM × 0.038 mm/rev = 210 mm/min.

Worked example: 1/16" drill in 1018 steel

HSS drill in low-carbon steel: 90 SFM.
RPM = 3.82 × 90 ÷ 0.0625 ≈ 5,500 RPM.
Feed for a 0.063 in drill in mild steel ≈ 0.0015 in/rev.
IPM = 5,500 × 0.0015 = 8.25 IPM.

Peck cycle by hole depth

1/16" drill: depth and canned cycle
Depth	Cycle	Peck	Note
3×D = 0.188 in (4.8 mm)	G81 (no peck)	None	Up to 3×D a sharp drill clears chips on its own.
5×D = 0.313 in (7.9 mm)	G73 chip-break	1 × D	Chip-break pecks; full retract if chips pack (soft aluminum, stainless).
8×D = 0.500 in (12.7 mm)	G83 full retract	0.5-1 × D, shrinking with depth	Retract to clear chips; reduce feed ~10-20% past 5×D.

Taps that use a 1/16" drill

1-64 — cut tap, 50% thread · tap speeds and feeds

Nearest drills

1.6 mm: 0.0630 in / 1.600 mm (+0.0005 in)
#52: 0.0635 in / 1.613 mm (+0.0010 in)
1.55 mm: 0.0610 in / 1.550 mm (-0.0015 in)
1.65 mm: 0.0650 in / 1.650 mm (+0.0025 in)

Drill speed calculator, prefilled for 1/16"Drill finder: sizes near 1/16"Fractional drill chart Decimal equivalent chart

Common questions

What is a 1/16" drill in decimal and mm?: 0.0625 in, or 1.588 mm; nearest number / letter drill: #52 (0.0635 in, +0.0010 in); nearest metric drill: 1.6 mm (0.0630 in, +0.0005 in).
What RPM for a 1/16" drill in steel?: In low-carbon steel (1018) an HSS 1/16" drill (0.0625 in) runs about 5,500 RPM at 90 SFM; a carbide drill about 18,330 RPM at 300 SFM. RPM = 3.82 × SFM ÷ D.
What feed for a 1/16" drill?: About 0.0015 in/rev in mild steel, 0.0014 in/rev in aluminum and 0.0010 in/rev in 304 stainless. At 5,500 RPM that is 8.25 IPM in steel (IPM = RPM × IPR).
What RPM for a 1/16" drill in aluminum?: 15,280 RPM with HSS (250 SFM) or up to 36,670 RPM with carbide (600 SFM), feeding about 0.0014 in/rev.
What tap uses a 1/16" drill?: 1-64 (cut tap, 50% thread).

Nearby drill sizes

Sources

Machinery's Handbook, 31st ed., Speeds and Feeds for Drilling, Reaming and Threading (Tables 17-23) — HSS and carbide drilling SFM (rounded).
RedLine Tools (Productivity Inc.) catalog p. 340, Cobalt & HSS Drills Speeds & Feeds — feed per rev by drill diameter and material (middle of the catalog range).
ASME B94.11M twist drills: number (#1-#80) and letter (A-Z) drill sizes; drill size reference.

Material feed multipliers (aluminum 1.3×, brass 1.1×, 4140 0.85×, stainless and titanium 0.7× the mild-steel feed) are JobLine estimates. Peck guidance is JobLine shop practice. Use your drill maker's data first.

Free for machinists & programmers

Put your skills on a free talent profile

Machines, controls, certs and saved calculations in one profile shops can find.

Create free profile

For your shop

Bring shift handoffs to your shop

Stop losing job status between shifts. Every station's notes, counts and issues, handed off cleanly.

See shift handoffs