PPS (Ryton) Speeds and Feeds (Milling, Drilling, Turning)

    Carbide end mills in PPS (Ryton): 400–1000 SFM. Also called polyphenylene sulfide. Chart row used: “Plastics” (Extruded).

    Starting point: carbide end mills

    RPM and IPM use the low end of the published range (400 SFM and the lowest chip load for each diameter range). RPM = SFM × 12 ÷ (π × D); IPM = RPM × flutes × chip load.

    PPS (Ryton) — inch end mills
    DiameterChip load (in/tooth)RPMIPM · 2 fluteIPM · 3 flute
    1/8".001012,22324.436.7
    1/4".00106,11212.218.3
    3/8".00204,07416.324.4
    1/2".00253,05615.322.9
    3/4".00402,03716.324.4
    1".00501,52815.322.9
    PPS (Ryton) — metric end mills (inch chip-load range the size falls in)
    DiameterChip load (in/tooth)RPMIPM · 2 fluteIPM · 3 flute
    3 mm.001012,93625.938.8
    6 mm.00106,46812.919.4
    10 mm.00253,88119.429.1
    12 mm.00253,23416.224.3
    16 mm.00402,42619.429.1
    20 mm.00501,94019.429.1
    Full published chip-load ranges
    • 1/32-1/8": .0010–.0020"
    • 1/8-1/4": .0010–.0030"
    • 1/4-3/8": .0020–.0045"
    • 3/8-1/2": .0025–.0060"
    • 1/2-3/4": .0040–.0100"
    • 3/4-1": .0050–.0120"

    Calculator — prefilled for PPS (Ryton)

    Results for Milling

    Spindle RPM
    3,056
    Feed
    30.6 IPM
    Chip load
    0.0023 in
    MRR
    1.15 in³/min
    Power
    — HP
    Torque
    — lbf·ft
    Programmed fz
    0.0025 in
    Actual SFM
    400
    Spindle use
    25%
    • Pick a material in the library below to estimate spindle power and torque.

    Material library

    Tool & coating guidance

    Grade, edge geometry and coating determine usable cutting data. Sharp polished edges can suit nonferrous work; substrate and geometry still govern. Coated vs uncoated carbide changes turning data only; no coating speed multiplier is inferred.

    Tool & cut parameters

    Manual values
    Chip thinning & cutter body
    %
    Radial factor ×1.09Angle factor ×1.00Programmed fz 0.0025 inMax chip hex 0.0023 in

    Fixed-angle peripheral estimate: hex = fz × radial factor × sin(KAPR). No radial correction at ≥50% engagement. Not a centered face-milling or ball-nose model. Sandvik geometry reference

    Insert styles, guidelines & formulas

    RPM = (SFM × 12) / (π × D) | Feed = RPM × programmed fz × effective zc | MRR = WOC × DOC × feed | HP = Kp × C × MRR × 1.1 ÷ 0.8 (Machinery's Handbook)

    Square (SEMT/SNMG)
    General purpose, 90° lead angle
    Round (RPMW/RCKT)
    Ramping, 3D contouring, high feed
    Triangular (TPMX)
    Light cuts, finishing
    Octagonal (ONMU)
    Face milling; HFM suitability is body-specific

    Milling Guidelines

    • Start at 70% of max SFM, increase gradually
    • Chip load too low → rubbing & heat buildup
    • Use climb milling when machine rigidity allows
    • Radial engagement >50% → reduce feed per tooth
    • Round inserts: best for ramp-in and 3D surfaces
    Open in the full calculator workspace

    Speeds by tool material

    Published starting ranges for PPS (Ryton) by operation and tool material. Rows marked * are estimates.

    PPS (Ryton) — speeds by tool material
    OperationToolSFMFeedSource row
    millingSolid carbide end mill400–10000.0025–0.0060 in/toothLakeshore Carbide · Plastics

    Machinist tips

    Chip thinning
    At light radial engagement (under half the cutter diameter) the real chip is thinner than the feed per tooth. Raise the feed to keep the chip at the chart value, or the tool rubs and wears.
    Climb vs conventional
    On a rigid CNC, climb mill so each tooth starts thick and exits thin. Use conventional milling on machines with backlash or on hard scale skins.
    Keep it cool
    Plastics melt before they dull a tool. Use sharp single or 2-flute tools, an air blast, and keep the feed up so the tool doesn't rub.

    Common questions

    What SFM should I use for PPS (Ryton)?
    Lakeshore Carbide – General Purpose End Mill Speeds & Feeds lists 400–1000 SFM for carbide end mills in the "Plastics" row. Start at the low end and adjust for your machine.
    What chip load for a 1/2" end mill in PPS (Ryton)?
    The published range for 3/8–1/2" carbide end mills is .0025–.0060" per tooth. At 400 SFM a 3-flute 1/2" end mill runs about 3056 RPM and 22.9 IPM.
    Are these values for HSS tools, drilling or turning?
    No. The source chart covers carbide end mills only. Use your drill or insert maker's data for drilling and turning.
    Delrin (Acetal) speeds and feedsPEEK speeds and feedsUHMW Polyethylene speeds and feeds

    Sources

    Starting values only. Adjust for rigidity, tool manufacturer data and machine.

    Free for machinists & programmers

    Put your skills on a free talent profile

    Machines, controls, certs and saved calculations in one profile shops can find.

    Create free profile
    For your shop

    Bring shift handoffs to your shop

    Stop losing job status between shifts. Every station's notes, counts and issues, handed off cleanly.

    See shift handoffs