#74 drill size
A #74 number (wire-gauge) drill is 0.0225 in (0.571 mm).
- Decimal inch
- 0.0225
- Millimeters
- 0.571
- Nearest 1/64
- 1/64" (+0.0069)
- Type
- number (wire-gauge) drill
Nearest equivalents in other systems
| System | Drill | Inch | mm | Difference |
|---|---|---|---|---|
| Fractional | 1/64" | 0.0156 | 0.397 | -0.0069 in |
| Metric | 0.55 mm | 0.0216 | 0.550 | -0.0008 in |
Speeds and feeds: in mild steel an HSS drill starts at about 15,280 RPM and 0.0007 in/rev (10.7 IPM); in 6061 aluminum about 42,440 RPM.
#74 drill speeds and feeds by material
Jobber-length twist drill, D = 0.0225 in. RPM = 3.82 × SFM ÷ D, rounded to 10. Feed per rev scales with diameter and material; IPM = RPM × IPR.
| Material | HSS SFM | HSS RPM | Carbide SFM | Carbide RPM | Feed (in/rev) | HSS IPM | Carbide IPM |
|---|---|---|---|---|---|---|---|
| Aluminum (6061) | 250 | 42,440 | 600 | 101,860 | 0.0007 | 29.7 | 71.3 |
| Brass / free-machining | 150 | 25,460 | 400 | 67,910 | 0.0006 | 15.3 | 40.8 |
| Low-carbon steel (1018) | 90 | 15,280 | 300 | 50,930 | 0.0007 | 10.7 | 35.6 |
| Alloy steel (4140, annealed) | 70 | 11,880 | 250 | 42,440 | 0.0007 | 8.32 | 29.7 |
| Stainless 304 | 40 | 6,790 | 150 | 25,460 | 0.0005 | 3.40 | 12.7 |
| Gray cast iron | 80 | 13,580 | 250 | 42,440 | 0.0005 | 6.79 | 21.2 |
| Titanium 6Al-4V | 25 | 4,240 | 100 | 16,980 | 0.0004 | 1.70 | 6.79 |
| Plastics (acetal) | 300 | 50,930 | 500 | 84,880 | 0.0013 | 66.2 | 110.3 |
Small drills: the computed RPM is above most spindles. Run at your spindle's maximum and keep the feed per rev; feed drops in proportion.
Metric: Vc (m/min) = SFM × 0.3048; feed (mm/rev) = in/rev × 25.4. In steel, 15,280 RPM × 0.018 mm/rev = 272 mm/min.
Worked example: #74 drill in 1018 steel
- HSS drill in low-carbon steel: 90 SFM.
- RPM = 3.82 × 90 ÷ 0.0225 ≈ 15,280 RPM.
- Feed for a 0.022 in drill in mild steel ≈ 0.0007 in/rev.
- IPM = 15,280 × 0.0007 = 10.7 IPM.
Peck cycle by hole depth
| Depth | Cycle | Peck | Note |
|---|---|---|---|
| 3×D = 0.068 in (1.7 mm) | G81 (no peck) | None | Up to 3×D a sharp drill clears chips on its own. |
| 5×D = 0.112 in (2.9 mm) | G73 chip-break | 1 × D | Chip-break pecks; full retract if chips pack (soft aluminum, stainless). |
| 8×D = 0.180 in (4.6 mm) | G83 full retract | 0.5-1 × D, shrinking with depth | Retract to clear chips; reduce feed ~10-20% past 5×D. |
Taps that use a #74 drill
No standard UNC, UNF or metric tap in our tables calls for a #74 drill. Use it for clearance, pilot or reamer prep holes.
Nearest drills
- 0.55 mm: 0.0216 in / 0.550 mm (-0.0008 in)
- 0.6 mm: 0.0236 in / 0.600 mm (+0.0011 in)
- #75: 0.0210 in / 0.533 mm (-0.0015 in)
- #73: 0.0240 in / 0.610 mm (+0.0015 in)
Common questions
- What is a #74 drill in decimal and mm?
- 0.0225 in, or 0.571 mm; nearest fractional drill: 1/64" (0.0156 in, -0.0069 in); nearest metric drill: 0.55 mm (0.0216 in, -0.0008 in).
- What RPM for a #74 drill in steel?
- In low-carbon steel (1018) an HSS #74 drill (0.0225 in) runs about 15,280 RPM at 90 SFM; a carbide drill about 50,930 RPM at 300 SFM. RPM = 3.82 × SFM ÷ D.
- What feed for a #74 drill?
- About 0.0007 in/rev in mild steel, 0.0007 in/rev in aluminum and 0.0005 in/rev in 304 stainless. At 15,280 RPM that is 10.7 IPM in steel (IPM = RPM × IPR).
- What RPM for a #74 drill in aluminum?
- 42,440 RPM with HSS (250 SFM) or up to 101,860 RPM with carbide (600 SFM), feeding about 0.0007 in/rev.
- What size is a #74 drill?
- 0.0225 in / 0.571 mm. The nearest other drills are 0.55 mm (0.0216 in), 0.6 mm (0.0236 in), #75 (0.0210 in).
Nearby drill sizes
Sources
- Machinery's Handbook, 31st ed., Speeds and Feeds for Drilling, Reaming and Threading (Tables 17-23) — HSS and carbide drilling SFM (rounded).
- RedLine Tools (Productivity Inc.) catalog p. 340, Cobalt & HSS Drills Speeds & Feeds — feed per rev by drill diameter and material (middle of the catalog range).
- ASME B94.11M twist drills: number (#1-#80) and letter (A-Z) drill sizes; drill size reference.
Material feed multipliers (aluminum 1.3×, brass 1.1×, 4140 0.85×, stainless and titanium 0.7× the mild-steel feed) are JobLine estimates. Peck guidance is JobLine shop practice. Use your drill maker's data first.
Put your skills on a free talent profile
Machines, controls, certs and saved calculations in one profile shops can find.
Create free profileBring shift handoffs to your shop
Stop losing job status between shifts. Every station's notes, counts and issues, handed off cleanly.
See shift handoffs