What is a 2.0 mm drill in decimal and mm?

0.0787 in, or 2.000 mm; nearest fractional drill: 5/64" (0.0781 in, -0.0006 in); nearest number / letter drill: #47 (0.0785 in, -0.0002 in).

What RPM for a 2.0 mm drill in steel?

In low-carbon steel (1018) an HSS 2.0 mm drill (0.0787 in) runs about 4,370 RPM at 90 SFM; a carbide drill about 14,550 RPM at 300 SFM. RPM = 3.82 × SFM ÷ D.

What feed for a 2.0 mm drill?

About 0.0019 in/rev in mild steel, 0.0018 in/rev in aluminum and 0.0013 in/rev in 304 stainless. At 4,370 RPM that is 8.30 IPM in steel (IPM = RPM × IPR).

What RPM for a 2.0 mm drill in aluminum?

12,130 RPM with HSS (250 SFM) or up to 29,110 RPM with carbide (600 SFM), feeding about 0.0018 in/rev.

What size is a 2.0 mm drill?

0.0787 in / 2.000 mm. The nearest other drills are #47 (0.0785 in), 5/64" (0.0781 in), 1.95 mm (0.0768 in).

2.0 mm drill size

A 2.0 mm metric drill is 0.0787 in (2.000 mm).

Decimal inch: 0.0787
Millimeters: 2.000
Nearest 1/64: 5/64" (+0.0006)
Type: metric drill

Nearest equivalents in other systems

Drills closest to 2.0 mm
System	Drill	Inch	mm	Difference
Fractional	5/64"	0.0781	1.984	-0.0006 in
Number / letter	#47	0.0785	1.994	-0.0002 in

Speeds and feeds: in mild steel an HSS drill starts at about 4,370 RPM and 0.0019 in/rev (8.30 IPM); in 6061 aluminum about 12,130 RPM.

2.0 mm drill speeds and feeds by material

Jobber-length twist drill, D = 0.0787 in. RPM = 3.82 × SFM ÷ D, rounded to 10. Feed per rev scales with diameter and material; IPM = RPM × IPR.

2.0 mm drilling speeds
Material	HSS SFM	HSS RPM	Carbide SFM	Carbide RPM	Feed (in/rev)	HSS IPM	Carbide IPM
Aluminum (6061)	250	12,130	600	29,110	0.0018	21.8	52.4
Brass / free-machining	150	7,280	400	19,400	0.0015	10.9	29.1
Low-carbon steel (1018)	90	4,370	300	14,550	0.0019	8.30	27.6
Alloy steel (4140, annealed)	70	3,400	250	12,130	0.0019	6.46	23.1
Stainless 304	40	1,940	150	7,280	0.0013	2.52	9.46
Gray cast iron	80	3,880	250	12,130	0.0011	4.27	13.3
Titanium 6Al-4V	25	1,210	100	4,850	0.0010	1.21	4.85
Plastics (acetal)	300	14,550	500	24,260	0.0031	45.1	75.2

Small drills: the computed RPM is above most spindles. Run at your spindle's maximum and keep the feed per rev; feed drops in proportion.

Metric: Vc (m/min) = SFM × 0.3048; feed (mm/rev) = in/rev × 25.4. In steel, 4,370 RPM × 0.048 mm/rev = 211 mm/min.

Worked example: 2.0 mm drill in 1018 steel

HSS drill in low-carbon steel: 90 SFM.
RPM = 3.82 × 90 ÷ 0.0787 ≈ 4,370 RPM.
Feed for a 0.079 in drill in mild steel ≈ 0.0019 in/rev.
IPM = 4,370 × 0.0019 = 8.30 IPM.

Peck cycle by hole depth

2.0 mm drill: depth and canned cycle
Depth	Cycle	Peck	Note
3×D = 0.236 in (6 mm)	G81 (no peck)	None	Up to 3×D a sharp drill clears chips on its own.
5×D = 0.394 in (10 mm)	G73 chip-break	1 × D	Chip-break pecks; full retract if chips pack (soft aluminum, stainless).
8×D = 0.630 in (16 mm)	G83 full retract	0.5-1 × D, shrinking with depth	Retract to clear chips; reduce feed ~10-20% past 5×D.

Taps that use a 2.0 mm drill

No standard UNC, UNF or metric tap in our tables calls for a 2.0 mm drill. Use it for clearance, pilot or reamer prep holes.

Nearest drills

#47: 0.0785 in / 1.994 mm (-0.0002 in)
5/64": 0.0781 in / 1.984 mm (-0.0006 in)
1.95 mm: 0.0768 in / 1.950 mm (-0.0020 in)
2.05 mm: 0.0807 in / 2.050 mm (+0.0020 in)

Drill speed calculator, prefilled for 2.0 mm Drill finder: sizes near 2.0 mm Metric drill chart Decimal equivalent chart

Common questions

What is a 2.0 mm drill in decimal and mm?: 0.0787 in, or 2.000 mm; nearest fractional drill: 5/64" (0.0781 in, -0.0006 in); nearest number / letter drill: #47 (0.0785 in, -0.0002 in).
What RPM for a 2.0 mm drill in steel?: In low-carbon steel (1018) an HSS 2.0 mm drill (0.0787 in) runs about 4,370 RPM at 90 SFM; a carbide drill about 14,550 RPM at 300 SFM. RPM = 3.82 × SFM ÷ D.
What feed for a 2.0 mm drill?: About 0.0019 in/rev in mild steel, 0.0018 in/rev in aluminum and 0.0013 in/rev in 304 stainless. At 4,370 RPM that is 8.30 IPM in steel (IPM = RPM × IPR).
What RPM for a 2.0 mm drill in aluminum?: 12,130 RPM with HSS (250 SFM) or up to 29,110 RPM with carbide (600 SFM), feeding about 0.0018 in/rev.
What size is a 2.0 mm drill?: 0.0787 in / 2.000 mm. The nearest other drills are #47 (0.0785 in), 5/64" (0.0781 in), 1.95 mm (0.0768 in).

Nearby drill sizes

Sources

Machinery's Handbook, 31st ed., Speeds and Feeds for Drilling, Reaming and Threading (Tables 17-23) — HSS and carbide drilling SFM (rounded).
RedLine Tools (Productivity Inc.) catalog p. 340, Cobalt & HSS Drills Speeds & Feeds — feed per rev by drill diameter and material (middle of the catalog range).
ASME B94.11M twist drills: number (#1-#80) and letter (A-Z) drill sizes; drill size reference.

Material feed multipliers (aluminum 1.3×, brass 1.1×, 4140 0.85×, stainless and titanium 0.7× the mild-steel feed) are JobLine estimates. Peck guidance is JobLine shop practice. Use your drill maker's data first.

Free for machinists & programmers

Put your skills on a free talent profile

Machines, controls, certs and saved calculations in one profile shops can find.

Create free profile

For your shop

Bring shift handoffs to your shop

Stop losing job status between shifts. Every station's notes, counts and issues, handed off cleanly.

See shift handoffs